Quickie Pulse Service Manual download pdf (Page 2)

PULSE 6 SERVICE MANUAL

PAGE 2

SEPT 2011 SUNRISE MEDICAL

Quickie Pulse 6 Service Manual Contents

Introduction 0.1

Basic Setup 0.2

Motor - Drive Gear engaged 0.2

Motor - Free-wheel 0.2

Multimeter Tutorial 0.3

The Multimeter 0.3

The Probes 0.3

The Ports 0.3

Symbols 0.4

Health and Safety 0.5

Good Working Practices 0.5

Battery Safety 0.5

Battery Chargers 0.6

EMI Warnings 0.6

Electro Static Discharge 0.8

Batteries 0.9

Battery Diagnostics 0.10

Battery Types 0.11

VR2 Remote Controller 0.12

VR2 Plugs/Connectors 0.13

R-NET Remote Controller 0.14

R-NET Remote Controller w/Display 0.15

R-NET Plugs/Connectors 0.16

Main Wiring Diagram VR2 (PLS) 0.17

Main Wiring Diagrams Rnet (PLS) 0.18

Main Wiring Diagram VR2 and RNET

(PLS6A/PLS6B) 0.19

Main Wiring Diagrams Actuators

(PLS6A/PLS6B) 0.20

VR2 Dual Attendant System Connection

Basic Tool List 0.21

Battery Connection Test 1.1

Check Battery Wire Harness 1.2

Circuit Breaker Test 1.2

Main Harness 1.2

Section 2

VR2 Remote Controller Display 2.1

The Maximum Speed Indicator Ripples 2.1

The Maximum Speed Indicator Flashes 2.1

Battery Gauge is Steady 2.1

Battery Gauge Flashes Slowly 2.1

Battery Gauge Steps Up. 2.1

Battery Gauge Blinks Once Every 2.5 Seconds 2.1

Battery Gauge Flashes Rapidly 2.1

Section 3

VR2 Controller Diagnostic Codes 3.1

One Bar - Low Battery Voltage 3.1

Two Bars - Left Motor Disconnected 3.1

Three Bars - Left Motor Wiring Trip 3.2

Four Bars- Right Motor Disconnected 3.2

Five Bars - Right Motor Wiring Trip 3.3

Six Bars - Charger Connected 3.4

Seven Bars - Possible Joystick Trip 3.4

Seven Bars + Speed Profile Indicator error 3.4

Eight Bars - Possible Control System Trip 3.4

Nine Bars - Solenoid Brake Trip 3.5

Ten Bars - High Battery Voltage 3.5

Section 4

R-net Troubleshooting Procedures 4.1

Chair Will Not Power Up 4.1

R-net Troubleshooting Procedures (cont.) 4.2

Section 5

R-net Fault Codes 5.1

Power Chair Displays a Fault on the Hand Control or

Omni 5.1

Table 1, Error Codes 5.1

Example of R-10 Fault Isolation 5.4

Power Chair Will Not Drive Full Speed 5.4

Power Chair Will Not Drive in Creep Speed When

Tilted 5.6

Tilt Will Not Operate 5.7

Section 6

Motor/Gearbox Inspection 6.1

Section 7

Removal Procedures 7.1

Battery Removal 7.1

Battery Installation 7.3

Motor and Gearbox Removal 7.4

Motor Removal for chairs after

S/N PLS-101919 and s/n prefix PLS6A &PLS6B 7.6

Control Module Removal 7.7

Shock Removal 7.9

Front Caster Arm Removal 7.10

Rear Caster Arm Removal 7.12

Front or Rear Caster Fork Removal 7.13

Caster Removal 7.14

Tilt Actuator and Micro-Switch Removal 7.15

Section 8

Seat/Back Width adjustment 8.1

Legrest adjustment 8.4

Back-rest Angle Adjustment 8.5

Powered elevating or articulating legrest 8.6

1 2 3 4 5 6 7 ... 71 72

Comments to this Manuals

No comments